|
 The Type SA- and SA-S fume
hoods are carefully engineered with air foil surfaces curved
to the air flow path, thereby creating a smoother air flow
pattern that can effectively remove air at a lower face velocity.
Thus, less room air is used when compared to a standard or
conventional fume hood.
Lab Fabricators’ fume hood superstructures are shipped
factory assembled with the light fixture, work surface, service
fixtures and electricals installed and tested. All hoods are
available in lengths from 3’-0" to 100’-0" and
may be customized to meet each user’s specific requirements.
The SA- and SA-S fume
hood superstructures are furnished with:
- The hood exterior is fabricated of 18 gauge, zinc-coated
and bondarized steel with a chemical resistant enamel to match
the base cabinet (furnished upon request).
- The interior of the SA- hood
is made of 1/4" thick, special heat, solvent and reagent
resistant composition stone that is treated with a chemical
resistant, clear vinyl for added protection. (Additional
hood liners are available upon request, including a white
modified resin/fiberglass, fiberglass reinforced polyester
(FRP), and white polypropylene.) The SA-S hood
is furnished with 18 gauge, T304 or T316 stainless steel
interior lining, baffles and adjustable dampers in a flat
sheet construction. (A seamless welded interior shell is
also available upon request.)
- The fume hood baffles have two adjustable air flow dampers
at the top and bottom for adjustment to light or heavy gases.
- The interior of the hood is illuminated with a vapor-proof
incandescent light fixture for added visibility.
- A vertically rising front sash has a 1/4" thick, laminated
safety glass window that is counter balanced with lead weights
for fingertip movement. Sash stops are available, upon request,
to further restrict the face opening of the hood.
- If the hood is furnished with a blower, the blower can be
enclosed within the hood ceiling or shipped separate. The
blower housing and wheel are coated
with a highly chemical resistant epoxy coating for extra protection
against corrosion.
Typical SA- and SA-S Fume
Hoods
| Catalog
Number |
Overall
Size L x H* |
Face
Opening w/32" H sash fully raised |
Exhaust
CFM @ 100 FPM face velocity |
Exhaust
S.P. |
Standard
Exhaust Blower Included |
| Composition
Stone Lined |
Stainless
Steel Lined |
| SA-4B |
SA-4SB |
48" |
101" |
7.9 SF |
790
CFM |
1/4" |
D8C |
| SA-5B |
SA-5SB |
60" |
101" |
10.3
SF |
1030
CFM |
1/4" |
D9C |
| SA-6B |
SA-6SB |
72" |
101" |
11.9
SF |
1190
CFM |
3/8" |
KE-11 |
| SA-7B |
SA-7SB |
84" |
101" |
14.3
SF |
1430
CFM |
1/4" |
KE-12 |
| SA-8B |
SA-8SB |
96" |
101" |
16.6
SF |
1660
CFM |
1/4" |
KE-12 |
| SA-4 |
SA-4S |
48" |
96" |
7.9
SF |
790
CFM |
1/4" |
None |
| SA-5 |
SA-5S |
60" |
96" |
10.3
SF |
1030
CFM |
1/4" |
None |
| SA-6 |
SA-6S |
72" |
96" |
11.9
SF |
1190
CFM |
3/8" |
None |
| SA-7 |
SA-7S |
84" |
96" |
14.3
SF |
1430
CFM |
1/4" |
None |
| SA-8 |
SA-8S |
96" |
96" |
16.6 SF |
1660
CFM |
1/4" |
None |
* Note: Overall height when installed on to a 35-3/4" high
base cabinet. Fume hoods may also be furnished without the support
cabinet(s) and/or work surfaces.
Note: Blowers, where required, may be shipped either factory
installed within the hood ceiling or separate from the hood superstructure.
Note: A complete system, including chemical resistant duct work,
is available.
Optional Features (but not limited to):
Safety Guard Low Face Velocity
Alarm
- Complies with OSHA regulations
- Factory installed and wired
Safety Guard Low Face Velocity Alarm
- Complies with OSHA regulations
- Factory installed and wired
Work Surface
- Cast epoxy resin, flat or dished
- "Solid Bond" stainless steel
Service Fixtures
- R400V remote control valve assembly with angled
serrated hose connection. Specify Index.
- R410V remote control water faucet with swivel goose
and hose connection for use with either cold or hot
water. Specify Index.
- R410V-MIX remote control mixing faucet with swivel
gooseneck and hose connection for use with hot and
cold water.
- A variety of deck mounted faucets and turret assemblies.
- Factory prepipe the remote control service fixtures
to either the upper or lower rear of the hood.
Sinks, Cup Sinks
- Epoxy resin
- Polypropylene
- Stainless steel
Electrical Items
- Duplex or single receptacles. Specify voltage and
amperage required.
- Motor starter switch or on/off switch for exhaust
blower. Specify if single or three phase and voltage.
Light Fixtures
- Two tube fluorescent light fixture (less bulbs).
- Explosion-proof, 150-300 watt incandescent light
fixture (less bulb).
Base
Cabinets
- Standard double cupboard cabinet
- Acid storage cabinet with composition stone lining.
(Vented doors and/or vent assembly to the hood’s
work surface are optional.)
- Solvent storage cabinet. (Vent assembly to the
hood’s work surface is optional.)
|
|
